Mosquito Magnet Executive Repair Manual

Browse online or download Repair Manual for Garden tools Mosquito Magnet Executive. Mosquito Magnet Executive Repair manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 13
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Mosquito Magnet DEFENDER / LIBERTY
Troubleshooting & Repair Steps©
NOTICE: With the exception of the reference to the Mosquito Web Site Information this guide and pictures are copyrighted. It shall not be copied and/or duplicated
in whole or in part - without the owner’s [Frank Piccione] expressed written permission. Warning! "Be very careful when working with electrical connections and hot
parts (e.g. igniters, combustion chambers, etc.). We are not responsible for any damage to your unit or harm to yourself or others that may occur when following the
directions listed in our repair manual."
Page 1 of 13
Mosquito Magnet© DEFENDER
The Mosquito Magnet (MM**) has a tendency to stop working after a few seasons.
IMPORTANT: Do your work outside because it can get a bit messy and you will not want any insects,
which have not died, flying around in your house!
Most problems are usually caused by a failed (or loose connection of the) thermocouple or igniter. Another
common failure cause is a clogged filter!
All Mosquito Magnets have the following in common: Power supply [Cord or Battery], liquid propane connector
consisting of a regulator, a propane mixing chamber, Schrader valve, LP solenoid valve, LP sprayer, igniter,
thermocouple, catalytic converter, fan, combustion chamber and a circuit board.
When you power on the unit, it turns on the fan and delivers airflow through the combustion chamber. Shortly
afterwards, the igniter is energized [it gets hot & ignites the propane], then the solenoid valve opens and allows
Liquid Propane to enter the combustion chamber through the sprayer. As soon as there is combustion, the
thermocouple sends feedback to the circuit board and the unit will continue to run. If there is no combustion the
Thermocouple will cause a shutdown of the unit. The propane is then converted in to CO2 via the catalytic
converter before exiting through the Plume Tube. The Schrader valve is the access point where you connect a
CO2 cartridge Quick Clear [blow out foreign matter from the tip of the sprayer] the unit via CO2 cartridge.
For troubleshooting, you may need a multi-meter, Phillips head screwdriver, a few wrenches, high-temperature
silicone adhesive, a 12-volt AC power supply, and Teflon tape [I suggest using Yellow - double density Teflon
tape which is often labeled as "Gas type" OR RectorSeal #5 pipe thread sealant].
Before you dive in opening the combustion chamber try the following:
1. Disconnect the gas line from the propane tank.
2. Using the reset tool, reset BOTH the tank and the regulator. Do this procedure twice. For
pictures & detailed instructions go to:
http://support.mosquitomagnet.com/help/common/opdrt.aspx
3. Use the Quick-Clear procedure. For additional info & pictures go to:
http://support.mosquitomagnet.com/help/common/qcv.aspx
a. Use up to FOUR CO2 cartridges, in a row, to clean out the Schrader valve. This is very
important.
b. Do not do it just once or twice.
4. Reconnect the Regulator to the propane tank.....with the unit turned OFF.
Now...SLOOOOOOOOWLY, very slowly open the propane tank valve... To the 3/4 open
position. I cannot emphasize how important it is to open the valve slowly. Otherwise, you can
lock up the regulator.
5. Now turn on the unit and let it run for five minutes, then check to see if you still have a fault
code**. If you do, you will have to take the combustion chamber apart to repair it.
If this does not do the trick, try the following:
1. Disconnect the propane tank from the regulator and hook it up to your BBQ... Turn on the BBQ
and let it run for about 10 minutes... You could have air in the propane tank.
2. Reconnect the regulator to the tank with the unit off, then disconnect the regulator, then
reconnect it... Open the valve on the tank 3/4 of the way open. Now turn on your unit...
3. If this does not do the trick, disconnect the regulator from the propane tank and give it a shake…
If you hear rattling there is a very good possibility you have a bad regulator.
If the unit is up and running...always be sure to turn off the gas supply a minute or two before you turn
off the unit...Then run a Quick-Clear procedure... This should be done every time the propane tank is
changed.
What causes the problem? When liquid propane is pumped there is always a chance that oil from the
pump gets mixed in with the propane. It is the oil and/or dirt which plug the filter just behind the spray
head. [See Figure 6]
Page view 0
1 2 3 4 5 6 ... 12 13

Summary of Contents

Page 1 - Mosquito Magnet© DEFENDER

Mosquito Magnet DEFENDER / LIBERTY Troubleshooting & Repair Steps© NOTICE: With the exception of the reference to the Mosquito Web Site Informat

Page 2 - Troubleshooting steps:

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 10 of 13 Picture #5 Picture#6 Components

Page 3 - Mosquito Magnet LIBERTY

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 11 of 13 This a bad one…Cleaning Needed!! Air filters located at th

Page 4

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 12 of 13 LIBERTY PLUS

Page 5

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 13 of 13

Page 6 - Page 6 of 13

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 2 of 13 Troubleshooting steps: First check out your power supply! The p

Page 7

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 3 of 13 Q. Unscrew the valve stem from the Schrader valve with valve st

Page 8 - Liberty Components

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 4 of 13 In the pict Figure 1. Power Supply Line Test> Showing va

Page 9

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 5 of 13 Circuit Board Connections: P

Page 10 - Page 10 of 13

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 6 of 13 Figure 6 – Remove screws holding the LP line in place. Figure 7

Page 11 - Page 11 of 13

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 7 of 13 Figure 14 – Open combustion chamber Clean this area w/ a small

Page 12 - LIBERTY PLUS

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 8 of 13 Glossary 1. MM-Mosquito Magnet 2. Fault Code ** a. Light soli

Page 13 - Page 13 of 13

Mosquito Magnet© DEFENDER / LIBERTY Troubleshooting & Repair Steps Page 9 of 13 Picture #2 Picture #3 Picture #4

Comments to this Manuals

No comments