Mosquito Magnet Liberty Owner's Manual download pdf (Page 7)

STARTING INSTRUCTIONS

Install additional attractant in designated compartment. (#18)

Install Net - You will hear a snap when bag is secure. (#20-23)

Close and turn latch on net door. Be sure net door is closed securely. (#24)

Make sure propane tank is fully closed. Attach propane regulator to propane tank. (#28)

Turn propane tank on (

slowly

turn valve knob all the way counter-clockwise). (#29)

Plug power connector into trap. (#30)

Plug AC adapter into electrical outlet. (#31) Caution: To avoid the risk of electrical shock, connect only to prop-

erly grounded outlets. Adaptor unit is not intended to be mounted.

Press “On/Reset” button – You will hear the fans start.

Yellow light will blink for approximately 5-7 minutes (Warm-Up Stage).

Following warm-up, yellow light will become constant for approximately 3 minutes (trap has reached specific

temperature).

Yellow light turns off, green light will turn on (trap is fully operational).

SHUT DOWN INSTRUCTIONS

To shut down the Liberty, simply close the valve on the propane tank and press the “Off” button.

DO NOT UNPLUG UNIT. MOSQUITO MAGNET LIBERTY MUST REMAIN PLUGGED IN FOR 5 MINUTES AFTER SHUT

DOWN OR UNTIL FAN STOPS TO AVOID HEAT DAMAGE.

Any open octenol or other added attractant packages should be removed and discarded. The net should also be

discarded prior to storing the Mosquito Magnet Liberty.

STORAGE: Mosquito Magnet Liberty should be stored indoors in the off-season. Cover unit with trap cover (available

at www.mosquitomagnet.com) or with a tarp and secure tightly at the bottom to keep out dust, spider webs and

other debris.

FOR BEST RESULTS

DO NOT MOVE TRAP WITH TANK ATTACHED! TANK MUST BE DISCONNECTED FROM

REGULATOR BEFORE TRAP IS RELOCATED TO AVOID DAMAGE TO REGULATOR

AND/OR TRAP. BE ADVISED, DAMAGE CAUSED FROM FAILURE TO COMPLY WITH

THIS INSTRUCTION IS NOT COVERED UNDER WARRANTY.

TANK CHANGING TIP

When attaching the regulator handle to a tank after a tank change, be sure to fully tighten the regulator handle

onto the tank. No need to use tools, but do turn the handle as far as possible by hand. When this is done, loosen

the handle 1/4 turn, then re-tighten the handle. Frequently this action will result in additional turns beyond the 1/4

turn. The purpose for this is to fully engage the regulator onto the tank. If the regulator is not fully engaged, the

flow of gas may be restricted to the point where the trap will show a gas empty code. If this occurs, press the off

button, close the tank valve, and remove the regulator from the tank. Re-attach the regulator and try again.

Trap can be left running in the rain.

If using lime or lawn regenerative compounds, be sure to shut down the Mosquito

Magnet first to prevent dust or fine mist from being drawn into trap and clogging net.

A standard, outdoor rated extension cord may be used to increase your trap area.

Octenol cartridge does not disintegrate. Smell will dissipate over time.

Your trap will begin capturing immediately, but allow 4-6 weeks with trap running 24 hours/day to significantly

reduce the biting insect population and interrupt breeding cycle.

Should you experience an interruption of power, be sure to restart the trap.

Clear door must be tightly secured to maximize catch.

Never spray insecticide in or around trap.

Use of protective

eyewear is

recommended

QUICK-CLEAR VALVE

Recommended for use at first tank change, and every second tank change thereafter. Also recommended for use

before seasonal storage to avoid build up of contaminant’s during off-season.

The Quick-Clear valve is used to clear out propane contaminants in the fuel line, which may block the flow of

propane from the tank to your Mosquito Magnet. The Quick-Clear valve is a gold, threaded knob located on the back

of your trap. It should be used with the black and gold, L-shaped adapter included in the box with your Mosquito

Magnet, and a 12 gram threaded CO

cylinder available on our website at www.mosquitomagnet.com or your local

Mosquito Magnet Dealer.

Important: Extinguish all smoking materials prior to use of Quick-Clear Valve.

Do not stand directly behind cylinder during operation.

Shut down your Mosquito Magnet. Let fan run until it stops. (about 5 mins.)

Close the propane tank valve by turning to the “Off” position. (turn the tank valve clockwise)

Remove the protective cap from Quick-Clear valve on your trap.

Hand-screw gold end of L-shaped adapter on to Quick-Clear valve, until tight.

Hand-screw the CO2 cylinder into black end of L-shaped adapter clockwise until hand tight.

Unscrew CO2 cylinder 1/4 turn only in counter-clockwise direction. The flow of CO2 will begin, lasting approxi-

mately 3 minutes. Be sure to allow CO2 to run out completely. (hissing will stop when cylinder is empty. Note:

CO2 cylinder will be cold to the touch)

Continue unscrewing the CO2 cylinder to remove. Discard empty CO2 cylinder after use, it is not reusable or

re-fillable. (Use caution when removing CO2 cylinder, as some residual CO2 may come out at this time.)

Remove L-shaped adapter by unscrewing gold end clockwise. (Remember to KEEP the black and gold adapter

for future use!)

Replace Quick-Clear valve protective cap, and proceed with normal start up of your Mosquito Magnet.

If use of Quick-Clear valve feature does not resolve starting trouble, contact Tech Support 877-699-8727.

1 2 3 4 5 6 7 8 9

Comments to this Manuals

No comments

Mosquito Magnet Liberty Owner's Manual Page 7

Comments to this Manuals

Related products and manuals for Garden tools Mosquito Magnet Liberty